Removing water from an air compressor is essential for optimum performance and preventing corrosion. It is pretty standard that our air compressor generates water inside the tank.Why is this happening? How can you solve it? or how to remove water from air compressor? Can it be avoided? In this article, we are going to explain the reasons why your air compressor starts generating water. We will give you the best solutions to eliminate this problem and prevent it from recurring.
If, on the other hand, your problem is that your air compressor has no pressure, check this specific article.
Why do compressors produce water? and how to remove water from air compressor?
Compressors are machines that generate compressed air to perform maintenance tasks. So, the air is absorbed from the atmosphere containing moisture during the compression process.
If you want to Use our air compressor, all this moisture is stored in the tank. The more the machine is used, the higher the moisture concentration.
This machine can cause future problems and hinder operation.
The main problem is the possible generation of internal rust. It accumulates inside the compressor and can be spread even by the pneumatic tools that we use.
Suppose your compressor generates a lot of water. How to clean the air compressor tank?
Do not worry!
Now you will get help to solve this problem in this article.
There are a few different ways to do this, but the most common is to use a dehumidifier.
A dehumidifier removes moisture from the air by cooling it down and condensing the water vapor into liquid form. The condensed water is then collected in a bucket.
Step 1: Gather Supplies and Tools
Gather supplies such as a dehumidifier, hose, and drain bucket. You’ll also need the following tools:
- The screwdriver opens up the air compressor’s motor compartment.
- Philip’s head screwdriver or ratchet is recommended to tighten and loosen screws.
Unscrew the drain pan from under the air compressor’s tank to collect moisture that drips out during this process. This task will speed up the drying process.
Step 2: Remove Top of Compressor
The first step is to remove any hoses attached to your air compressor, then place them on a level surface. Using a screwdriver, remove the screws that hold the top of the compressor in place. It’s a good idea to keep track of where each screw goes so that you can put everything back together correctly.
Step 3: Locate the Motor
The next step is to locate the motor. This motor is typically found in the lower-left corner of your air compressor. To remove water from the air compressor- Unscrew the screws that hold it in place. Place these screws to the side; you’ll need them later.
Step 4: Rinse out Motor
Rinse out the motor with water to remove any dirt, grime, and oil that’s inside. Try using a vacuum cleaner for this step if possible; it’s much easier to remove debris this way.
Step 5: Drain the Tank
Tank To drain the tank, you’ll need to pull out the drain pan that rests underneath it. Use Philip’s head screwdriver or ratchet to loosen and tighten screws that hold it in place. This step will collect any excess moisture that drips out while you’re removing the water from the air compressor.
Step 6: Install Dehumidifier Now
It’s time to install the dehumidifier. First, remove the drain hose from the drain pan and attach it to the dehumidifier’s drainage outlet. You can place the other end of the hose in a bucket or container to collect the condensed water.
Attach the dehumidifier’s power cord to an outlet and turn it on. The dehumidifier will start to remove moisture from the air.
Step 7: Monitor the Dehumidifier
Monitor the dehumidifier to make sure it’s removing enough water from the air. If it’s not, you may need to adjust the settings.
Once the water tank is full, turn off the dehumidifier and empty the tank into a sink or outside drain. Repeat this process until all of the water has been removed from the air compressor.
Reattach the top of the compressor, making sure to place each screw back in its original spot. Reconnect any disconnected hoses and screw the drain pan back in place.
You need to turn on the air compressor and check for leaks. If you do everything correctly, you’re good to go!
Water can cause a lot of damage to an air compressor, so it’s essential to remove it regularly. It prevents it from rusting, corroding, and swelling.
Tools you will need a screwdriver, ratchet, dehumidifier, bucket, or container to collect condensed water.
see also 10 best small air compressor in 2022
Step 1: Locate the Drain Plug
The first step is to locate the drain plug. This drain plug is a small hole located at the bottom of the air compressor. Place a bucket or container under this hole to catch any excess moisture that drips out while you’re removing the water from the air compressor.
Step 2: Drain the Air Compressor
Use a screwdriver to remove the drain plug. This driver will allow all excess moisture to drain your air compressor into your bucket or container. Remember, this is where most of the water in your air compressor is located, so give it a little time to drain.
Step 3: Remove the Drain Pan
Use your screwdriver or ratchet to remove the screws from the drain pan. These screws will allow you to empty any excess water that slipped past the drain plug into a bucket or container for collection.
Step 4: Rinse Out Motor and Compressor
Now it’s time to rinse out the motor and compressor. It will help remove any built-up sediment or water collected inside. You can use a garden hose for this, but be careful not to get too much moisture inside the air compressor. Too much water can cause damage and will necessitate further repairs.
Step 5: Connect the Compressor to a Power Source
Connect the air compressor to a power source and turn it on for five minutes. This compressor will help dry out any excess moisture remaining inside. You don’t want to overdo it, though, because this can cause damage if your air compressor becomes too hot. Just give it a quick five minutes and then turn it off.
Step 6: Turn Off Power Source
After you’ve let your air compressor drain for five minutes, make sure it’s off and disconnect the power source from the power outlet.
see also 10 best small air compressor for cleaning PC
Step 7: Drain Air Compressor Again
Please remove all of the remaining water from your air compressor by draining it again. Remove the drain pan and clean it out before replacing it. Make sure you put the drain plug back in securely to prevent any leakage during use.
Step 8: Let Your Air Compressor Sit
Once your air compressor is dry, let it sit for at least an hour before using it. This air compressor will help reduces moisture buildup due to condensation.
Step 9: Use Your Air Compressor
After your air compressor has dried, you can use it as usual. Enjoy a long life by following these steps every week. Or drain all of the moisture from your air compressor. You’ll save money on repairs and extend its lifespan in the process.
Recent Comments